To make the mould, which is only a temporary thing, you may use any rough board, or boards nailed together with cleats to hold them. The mould should be 2 feet 6 inches long and 1 foot 4 inches high. Fig. 111 will show you how to cut off the ends to give the proper slant. The dotted lines show the board before it is trimmed in shape. By measuring along the edge of the board from each end 10.8 inches and marking the points, and then, with a carpenter's pencil ruling the diagonal lines to the other edge and ends of the board, the triangles may be sawed off with a hand saw.
Fig. 111 shows where the mould is to be placed in the center of the two side boards. As the boards in this diagram are supposed to be on the slant, and consequently in the perspective, they do not appear as wide as they really are. The diagram is made also with the ends of the side boards free so as to better show the position of the mould. But when the side boards are sprung apart and the mould placed in position (Fig. 113), it will appear as in Fig. 116 or Fig. 117. Fig. 115 shows the shape of the stem-posts to be set in both bow and stern and nailed securely in place.
When you have gone thus far fit in two temporary braces near the bow and stern, as shown in Fig. 117. These braces are simply narrow pieces of boards held in position by nails driven through the outside of the boat, the latter left with their heads protruding, so that they may be easily drawn when necessary.
Now turn the boat over bottom up and you will find that the angle at which the sides are bent will cause the bottom boards to rest upon a thin edge of the side boards, as shown in Fig. 119. With an ordinary jack-plane trim this down so that the bottom boards will rest flush and snug, as in Fig. 120.
How to Calk a Boat so That It Won't Leak
If you wish to make a bottom that will never leak, not even when it is placed in the water for the first time, plane off the boards on their sides, so that when fitted together they will leave a triangular groove between each board, as shown in Fig. 118½. These grooves will show upon the inside of the boat, and not upon the outside, and in this case the calking is done from the inside and not from the outside. They are first calked with candlewick, over which putty is used, but for a rough boat it is not even necessary to use any calking. When the planks swell they will be forced together, so as to exclude all water.
To fasten the bottom on the boat put a board lengthwise at the end, as shown in Fig. 121. One end shows the end board as it is first nailed on, and the other end shows it after it has been trimmed off to correspond with the sides of the boat. Now put your short pieces of boards for the bottom on one at a time, driving each one snug up against its neighbor before nailing it in place and leaving the rough or irregular ends of each board protrude on each side, as shown at the right-hand end of Fig. 121.
When all the boards are nailed in place (by beginning at one end and fitting them against each other until the other end is reached) they may be trimmed off with a saw (Fig. 121) and your boat is finished with the exception of the thwarts, or seats.
If you intend to propel this with paddles like a canoe, you will need a seat in the centre for your passenger, and this may be placed in the position occupied by the form (Figs. 111 and 117) after the latter is removed. To fit a seat in it is only necessary to cut two cleats and nail them to the sides of the boat for the seat to rest upon and saw off a board the proper length to fit upon the cleats. It would be well now to fasten the braces in the bow and stern permanently, adjusting them to suit your convenience. The seat should be as low as possible for safety. With this your paddling dory is finished, and may be used even without being painted. A coat of paint, however, improves not only the looks but the tightness and durability of any boat.
We have now advanced so far in our boat-building that it becomes necessary that the beginner should learn more about boats and boating, and since this book is written for beginners, we will take it for granted that they know absolutely nothing about the subject and will give all the rudimentary knowledge for landlubbers in the next chapter.
CHAPTER VIII
THE LANDLUBBER'S CHAPTER
There are a few common terms with which all who venture on the water should be familiar, not only for convenience, but for prudential reasons.
Accidents are liable to happen to boats of all descriptions, and often the safety of property and life depend upon the passengers' ability to understand what is said to them by the officers or sailors in charge of the craft.
To those who are familiar with the water and shipping it may seem absurd to define the bow and stern of a boat, but there are people who will read this book who cannot tell the bow from the stern, so we will begin this chapter with the statement that
The bow is the front end of the boat, and
The stern is the rear end of the boat.
For'ard is toward the bow of the boat.
Aft is toward the stern of the boat. Both terms are used by sailors as forward and backward are used by landsmen.
The hull is the boat itself without masts, spars, or rigging. A skiff and a birch-bark canoe are hulls.
The keel is the piece of timber running along the centre of the bottom of the hull, like the runner of a skate, and used to give the boat a hold on the water, so that she will not slide sideways.
When you are sitting in the stern of a boat, facing the bow, the side next to your right hand is the right-hand side of the boat, and the side next to your left hand is the left-hand side of the boat. But these terms are not used by seamen; they always say
Starboard for the right-hand side of the boat, and
Port for the left-hand side of the boat. Formerly the left-hand side was called the larboard, but this occasioned many serious mistakes on account of the similarity of the sound of larboard and starboard when used in giving orders.
Red and Green Lights
After dark a red light is carried on the port side and a green light on the starboard side of all vessels in motion. If you can remember that port wine is red, and that the port light is of the same color, you will always be able to tell in which direction an approaching craft is pointing by the relative location of the lights.
Port your helm and show your red!
Green to green and red to red,
You're all right, and go ahead!"
If you are a real landlubber, the verse quoted will be of little service, because you will not know how to port your helm. In fact, you probably will not know where to look for the helm or what it looks like; but only a few of our readers are out-and-out landlubbers, and most of them know that the helm is in some way connected with the steering apparatus.
The rudder is the movable piece of board at the stern of the boat by means of which the craft is guided. The rudder is moved by a lever, ropes, or a wheel.
The tiller is the lever for moving the rudder, or the ropes used for the same purpose (Fig. 123).
The wheel is the wheel whose spokes end in handles on the outer edge of the rim, or felly, and it is used for moving the rudder (Fig. 124).
The helm is that particular part of the steering apparatus that you put your hands on when steering.
The deck is the roof of the hull.
The centreboard is an adjustable keel that can be raised or lowered at pleasure. It is an American invention. The centreboard, as a rule, is only used on comparatively small vessels. The inventor of the centreboard is Mr. Salem Wines, who kept a shop on Water Street, near Market Slip, and, when alive, was a well-known New York boat-builder. His body now lies in Greenwood Cemetery, and upon the headstone of his grave is the inscription, "The Inventor of the Centreboard."
For sailing, the boat, or hull, is rigged with masts and spars for spreading the sails to catch the wind.
The masts are the upright poles, or sticks, that hold the sails.
The yards are the poles, or sticks, at right angles with the masts that spread the sails.
The boom is the movable spar at the bottom of the sail.
The gaff is the pole, or spar, for spreading the top, or head, of the sail (Fig. 125).
The sail is a big canvas kite, of which the boom, gaff, and masts are the kite-sticks. You must not understand by this that the sail goes soaring up in the air, for the weight of the hull prevents that; but if you make fast a large kite to the mast of a boat it would be a sail, and if you had a line long and strong enough, and should fasten any spread sail to it, there can be no doubt that the sail would fly.
The spars are the masts, bowsprit, yards, and gaffs.
The bowsprit is the stick, or sprit, projecting from the bow of the boat (Fig. 161, Sloop).
The foremast is the mast next to the bow—the forward mast (Fig. 159, Ship).
The mainmast is the second mast—the mast next to the foremast.
Mizzen-mast is the mast next to and back of the mainmast (Fig. 159, Ship).
The rigging of a boat consists of the ropes, or lines, attached to its masts and sails, but a boat's rig refers to the number of masts as well as to the shape of its sails.
Stays are strong ropes supporting the masts, fore and aft.
Shrouds are strong ropes reaching from the mastheads to the sides of the vessel; supports for the masts, starboard and port.
Ratlines are the little ropes that form the steps, or foot ropes, that run crosswise between the shrouds.
The painter is the rope at the bow of a small boat, used for the same purpose as is a hitching-strap on a horse.
The standing rigging consists of the stays and shrouds.
The running rigging consists of all the ropes used in handling yards and sails.
The sheets are the ropes, or lines, attached to the corners of sails, by which they are governed (Fig. 126).
The main sheet is the rope that governs the mainsail.
The jib-sheet is the rope that governs the jib-sail.
The gaskets are the ropes used in lashing the sails when furled.
The braces are the ropes used in swinging the yards around.
The jib-stay is the stay that runs from the foremast to the bowsprit.
The bob-stay is practically an extension of the jib-stay and the chief support of the spars. It connects the bow of the boat with the bowsprit and prevents the latter from bobbing up and down.
Besides the port and starboard sides of a boat there are the windward and leeward sides. Do not understand by this that the boat has four sides, like a square. Windward may be the port or the starboard side, according to the direction the wind blows; because
Windward means the side of the boat against which the wind blows—the side where the wind climbs aboard; or it may mean the direction from which the wind comes. The opposite side is called
Leeward—that is, the side of the boat opposite to that against which the wind blows, where the wind tumbles overboard, or the side opposite to windward. When you are sailing you may be near a
Lee Shore—that is, the shore on your lee side against which the wind blows; or a
Windward Shore—that is, the land on your windward side from which the wind blows.
All seamen dread a lee shore, as it is a most dangerous shore to approach, from the fact that the wind is doing its best to blow you on the rocks or beach. But the windward shore can be approached with safety, because the wind will keep you off the rocks, and if it is blowing hard, the land will break the force of the wind.
In a canoe or shell the boatman sits either directly on the bottom, or, as in the shell, very close to it, and the weight of his body serves to keep the boat steady, but larger crafts seldom rely upon live weights to steady them. They use
Ballast—that is, weights of stone, lead, iron, or sand-bags, used to balance the boat and make her steady.
As has been said before in this chapter, the sail is a big canvas kite made fast to the boat and called a sail, but the ordinary kite has its covering stretched permanently on rigid sticks.
The sail, however, can be stretched to its full extent or only partially, or it may be rolled up, exposing nothing but the masts to the force of the wind. To accomplish all this there are various ropes and attachments, all of which are named.
It is quite important that the beginner should know the names of all the
Parts of a Sail
Luff.—That part of the sail adjoining the mast—the front of the sail (Fig. 127).
Leach.-That part of the sail stretched between the outer or after end of the boom and the outer end of the gaff—the back part of the sail (Fig. 127).
Head.—That part of the sail adjoining the gaff—the top of the sail.
Foot.—That part of the sail adjoining the boom—the bottom of the sail (Fig. 127).
Clews.—A general name for the four corners of the sail.
Clew.—The particular corner at the foot of the sail where the leach and boom meet (Fig. 127).
Tack.—The corner of the sail where boom and mast meet (Fig. 127).
Throat, or Nock.—The corner of the sail where gaff and mast meet (Fig. 127).
Peak.—Corner of the sail where the leach and gaff meet (Fig. 127).
How to Steer a Boat
When you wish your boat to turn to the right push your helm to the left. This will push the rudder to the right and turn the boat in that direction. When you wish your boat to turn to the left push your helm to the right. In other words, starboard your helm and you will turn to the port (Fig. 128). Port your helm and you will turn to the starboard (Fig. 129).
From a reference to the diagram you may see that when you port your helm you move the tiller to the port side of the boat, and when you starboard your helm you move your tiller to the starboard side of the boat (Fig. 128), but to ease your helm you move your helm toward the centre of the boat—that is, amidships.
How to Sail a Boat
If you fasten the bottom of a kite to the ground, you will find that the wind will do its best to blow the kite over, and if the kite is fastened to the mast of a toy boat, the wind will try to blow the boat over.
In sailing a boat the effort of the wind apparently has but one object, and that is the upsetting of the boat. The latter, being well balanced, is constantly endeavoring to sit upright on its keel, and you, as a sailor, are aiding the boat in the struggle, at the same time subverting the purpose of the wind to suit your own ideas. It is an exciting game, in which man usually comes out ahead, but the wind gains enough victories to keep its courage up.
Every boat has peculiarities of its own, and good traits as well as bad ones, which give the craft a personal character that lends much to your interest, and even affects your sensibilities to the extent of causing you to have the same affection for a good, trustworthy craft that you have for an intelligent and kind dog or horse.
A properly balanced sail-boat, with main sheet trimmed flat and free helm, should be as sensitive as a weathercock and act like one—that is, she ought to swing around until her bow pointed right into the "eye of the wind," the direction from which the wind blows. Such a craft it is not difficult to sail, but it frequently happens that the boat that is given to you to sail is not properly balanced, and shows a constant tendency to "come up in the wind"—face the wind—when you are doing your best to keep her sails full and keep her on her course. This may be caused by too much sail aft. The boat is then said to carry a weather helm.
Weather Helm.—When a boat shows a constant tendency to come up in the wind.
Lee Helm.—When a boat shows a constant tendency to fall off the wind—that is, when the wind blows her bow to the leeward. This is a much worse trait than the former, and a boat with a lee helm is a dangerous boat. It may be possible to remedy it by adding sail aft or reducing sail forward, which should immediately be done.
In spite of the fact, already stated, that the wind's constant effort is to capsize a boat, there is little or no danger of a properly rigged boat upsetting unless the sheets are fast or hampered in some way. When a sail-boat upsets it is, of course, because the wind blows it over. Now, the wind cannot blow a boat over unless the boat presents some surface larger than its hull for the wind to blow against, and the sail is the only object that offers enough surface to the breeze to cause an upset.
Top view of boats, showing position of helm and boom.
| |
If the sheet is slackened, the sail will swing around until it flaps like a flag and only the thin edge is presented to the wind; and a boat that a flag will upset is no boat for beginners to trust themselves in. True, the boom may be very long and heavy enough to make it dangerous to let so much of it overboard, but this is seldom the case. A good sailor keeps his eyes constantly on the sails and trims them to take advantage of the slightest favorable breeze. In place of losing control of his sail by letting go the sheets he will ease the tiller so as to "spill" part of the wind that is, let the forward part, or luff, of the sail shake a bit. Or, in case of a sudden puff of wind, he may deem it necessary to "luff"—that is, let her shake—and slacken the sheets too.
Trimmed Flat.—Sheets hauled in until the boom is only a little to the leeward of the helm (Fig. 130).
Close-hauled.—Sheets trimmed flat and the boat pointing as near as possible to the eye of the wind. Then the sail cannot belly, and is called flat (Fig. 130).
To Sail Close-hauled
The skipper must watch that his sail does not flap or ripple at the throat, for that means that he is pointing too close to the wind and that some of the breeze is blowing on both sides of his sail, which even a novice can see will retard the boat.
Upon discovering a rippling motion at the luff of the sail put the helm up—that is, move the tiller a little to windward until the sail stops its flapping.
Before the Wind.—When the wind is astern; sailing with the wind; sailing directly from windward to leeward (Fig. 131).
In order to reach the desired point it is often expedient to sail before the wind, but unless the wind is light, beginners had better not try this. To sail before the wind you let your sheets out until the boom stands at almost right angles with the boat. Keep your eye on the sail and see that it does not flap, for if the man at the helm is careless and allows the boat to point enough away from the direction of the wind to allow the wind to get on the other side of the sail, the latter will swing around or jibe with such force as to endanger the mast, if it does not knock some one overboard.
The price of liberty is constant vigilance, and the price of a good sail is the same. I have seen a mast snapped off clean at the deck by a jibe, and once when out after ducks every one was so intent upon the game that proper attention was not paid to the sail. The wind got round and brought the boom with a swing aft, knocking the captain of our boat club overboard. Had the boom hit him in the head and stunned him, the result might have been fatal.
Wing and Wing.—When a schooner goes before the wind with one sail out at nearly right angles on the port side and the other in the same position on the starboard side she is said to be wing and wing and presents a beautiful sight.
Tacking.—Working to the windward by a series of diagonal moves.
Legs.—The moves or diagonal courses made in tacking. It is apparent to the most unthinking observer that no vessel propelled by sail can move against the direct course of the wind—that is, nothing but electricity, naphtha, steam, or some such power can drive a boat into the eye of the wind. But what cannot be accomplished in a direct manner can be done by a series of compromises, each of which will bring us nearer to the desired point.
First we point the boat to the right or left, as the case may be, as near or as close to the wind as the boat will sail. Then we come about and sail in the other direction as close as practicable to the eye of the wind, and each time we gain something in a direct line.
When your boat changes its direction on a tack it is done by "jibing," or "coming about."
Jibing.—With the wind on the quarter, haul the main boom aft or amidship with all possible speed, by means of the main sheets (Fig. 132), and as the wind strikes the sail on the other side let it out as deliberately as possible until it reaches the position desired (Fig. 133).
Beginners should never attempt to jibe, for if there is more than a capful of wind, the sail will probably get away from them, and, as described in going before the wind, some disaster is liable to occur. Experts only jibe in light winds, and frequently lower the peak, so as to reduce sail, before attempting a jibe.
Coming About
When you wish to come about see that all the tackle, ropes, etc., are clear and in working order, and that you are making good headway; then call out: "Helm's a-lee!" or "Ready about!" and push the tiller in the direction opposite to that from which the wind blows—that is, to the lee side of the boat. This will bring the bow around until the wind strikes the sail upon the side opposite to that which it struck before the helm was a-lee (Figs. 134, 135, 136, 137).
If you are aboard a sloop or schooner, ease off the jib-sheet, but keep control of it, so that as the boat comes up to the wind you can make the jib help the bow around by holding the sheets so as to catch the wind aback. When the bow of the craft has passed the eye of the wind and the sail begins to fill give the order to make fast, or trim, the jib, and off you go upon the opposite tack, or on a new leg.
If the wind is light, or if, for any cause, the boat works slowly, you can sometimes help her by trimming in the main sheet when you let the jib-sheet fly. In the diagram of coming about no jib is shown.
Wearing is a term sometimes used in place of jibing.
In a Thunder-storm
A thunder-storm is always an uncertain thing. There may be a veritable tornado hidden in the black clouds that we see rising on the horizon, or it may simply "iron out the wind"—that is, go grumbling overhead—and leave us becalmed, to get home the best way we can; generally by what the boys call a "white-ash breeze"—that is, by using the sweeps or oars.
On Long Island Sound a thunder-storm seems to have certain fixed rules of conduct. In the first place, it comes up from the leeward, or against the wind. Just before the storm strikes you for an instant the wind ceases and the sails flap idly. Then look out! for in nine cases out of ten you are struck the next moment by a sudden squall from exactly the opposite direction from which the wind blew a moment before.
What to Do
Make for the nearest port with all speed, and keep a man at the downhaul ready at a moment's notice to lower sail. The moment the wind stops drop the sail and make everything snug, leaving only bare poles. When the thunder-squall strikes you, be it ever so hard, you are now in little danger; and if the wind from the new quarter is not too fresh, you can hoist sail again and make the best of your way to the nearest port, where you can "get in out of the wet."
If the wind is quite fresh keep your peak down, and with a reefed sail speed on your way. If it is a regular howler, let your boat drive before the wind under bare poles until you can find shelter or until it blows over, and the worst mishap you are likely to incur is a good soaking from the rain.
Shortening Sail.—Just as soon as the boat heels over too far for safety, or as soon as you are convinced that there is more wind than you need for comfortable sailing, it is time to take a reef—that is, to roll up the bottom of the sail to the row of little ropes, or reefing points, on the sail and make fast there. This, of course, makes a smaller sail, and that is what you wish.
While under way it will be found impossible to reef a sail except when sailing close-hauled. So the boat is brought up into the wind by pushing the helm down, as if you intended to come about. When possible it is better to lower the sail entirely before attempting to put in a reef.
To Reef Without Lowering Sail
It sometimes happens that on account of the proximity of a lee shore, and the consequent danger of drifting in that direction, or for some other equally good reason, it is inadvisable to lower sail and lose headway. Under such circumstances the main sheet must be trimmed flat, keeping the boat as close as possible to the wind, the helm must be put up hard a-lee, and jib-sheet trimmed to windward (Fig. 138).
When this is done the wind will hit the jib, "paying her head off," or pushing her bow to leeward, and this tendency is counteracted by the helm and mainsail, bringing the bow up into the wind. This keeps the boat squirming. Lower the mainsail until the row of reef points is just on a line with the boom, keeping to the windward of the sail. Tie the first point—that is, the one on the luff rope—then the one on the leach, being careful to stretch out the foot of the sail. Then tie the remaining points, always making a square or reefing knot. Tie them to the jack-stay on the boom or around the boom.
The Reef or Square Knot
To Shake Out a Reef
Starboard Tack.—When the main boom is over the port side.
Port Tack.—When the main boom is over the starboard side.
Right of Way.—All boats sailing on the starboard tack have the right of way over all those on the port tack. In other words, if you are on the starboard tack, those on the port tack must keep out of your way. Any boat sailing close-hauled has the right of way over a boat sailing free.
Lights for Canoe
A canoe under sail at night should have an uncolored lantern hung to her mizzen-mast to notify other craft that she is out and objects to being run down. The light is put on the mizzen so that it may be behind the skipper and not dazzle him.
What you have read in the foregoing pages will not be found very difficult to remember, but there is only one way to learn to sail and that is by sailing. If possible, sail with some one who is a good seaman. If this sort of companion cannot be had, try it alone on smooth water and with short sail until you accustom yourself to the boat and its peculiarities. No boy ever learned to skate or swim from books, but books often have been helpful in giving useful hints to those who were really learning by practical experience.
Some Do Nots
Do not carry too much sail.
Do not sail in strange waters without chart or compass.
Do not forget your anchor.
Do not forget your paddles or oars.
Do not attempt to learn to sail before you know how to swim.
Do not sit on the gunwale.
Do not put the helm down too suddenly or too far.
Do not let go the helm.
Do not mistake caution for cowardice.
Do not be afraid to reef.
Do not fear the ridicule of other landlubbers.
Do not fail to keep the halyards and sheets clear.
Do not jibe in a stiff wind.
Do not fail to keep your head in times of emergency.
Do not make a display of bravery until the occasion demands it.
Do not allow mistakes or mishaps to discourage you.
Do not associate with a fool who rocks a boat.
You will soon become an expert and be able to engage in one of our most exhilarating, healthy, and manly sports and earn the proud distinction of being a good small-boat sailor.
It is Necessary to Learn to Swim
From the parents' point of view, nowhere that a boy's restless nature impels him to go is fraught with so much peril as the water, and nowhere is a boy happier than when he is on the water, unless it is when he is in it. Nowhere can be found a better school for his young mind and body than that furnished by boating. Hence it appears to be the imperative duty for parents personally to see that their children are taught to swim as soon as their little limbs have strength enough to make the proper motions.
Boating-Clothes
In aquatic sports of all kinds, if you expect to have fun, you must dress appropriately. You should have a suit of old clothes that you can change for dry ones when the sport is over. When boating, it is nonsense to pretend you can keep dry under all the varying conditions of wind and weather. If your purse is small, and you want a good rowing-suit, it can be made of last winter's woollen underclothes, and will answer for the double purpose of rowing and bathing.
How to Make a Bathing-Suit
First take an old woollen undershirt and cut the sleeves off above the elbows. Then coax your mother, aunt, or sister to sew it up in front like a sweater, and hem the edges of the sleeves where they have just been cut off.
Next take a pair of woollen drawers and have them sewed up in front, leaving an opening at the top about four inches in length; turn the top edge down all around to cover a piece of tape that should be long enough to tie in front. Have this hem or flap sewed down to cover the tape, and allow the two ends of the tape to protrude at the opening in front. The tape should not be sewed to the cloth, but should move freely, so that you can tighten or loosen it at will. Cut the drawers off at the knees and have the edges hemmed, and you will have a first-class bathing or rowing-suit.
If woollen clothes are not to be had, cotton will do, but wool is coolest and warmest, as the occasion may require.
When rowing wear old socks, woollen ones if you have them, and old shoes cut down like slippers. The latter can be kicked off at a moment's notice, and, if lost, they are of no value, and may be easily replaced.
When on shore a long pair of woollen stockings to cover your bare legs and a sweater to pull over your sleeveless shirt are handy and comfortable, but while sailing, paddling, or rowing in hot weather the rowing-suit is generally all that comfort requires. Of course, if your skin is tender, you are liable to be terribly sunburned on your arms, neck, and legs; but