Plate 5. shews the whole Mounting of a Turnep-drill. Fig. 1. is a Plough, but little differing from the Drill-plough last mentioned. A, A, are the Two Limbers, differing in nothing from the other, except that they are lighter, not being above Two Inches Diameter, behind the Bar: They are drawn in the same manner as the other. Their Bar B is distant from the Plank Three Inches, being shoulder’d at each End, with a very thin flat Tenon, passing thro’ each Limber, and pinn’d on their Outsides, as at a a. We do not pin in this Bar thro’ the Limbers, lest the Holes should make these very small Limbers the weaker in that Part. C, the Plank, Two Feet and an Inch long, Five Inches broad, and an Inch and a quarter thick. D, D, the Two double Standards, or Two Pair of Standards, placed into the Plank with Shoulders above, and Tenons pinn’d underneath the Plank, and are Thirteen Inches high above it: These serve for a Pair of Marking-wheels, when Turneps are drill’d on the Level, to keep the Rows all parallel, and at what Distance you please, by setting them according to the Rule already laid down.

Sometimes we place the double Standards into the Plank of the Wheat-drill, in the same manner that these are placed.

We take off the inner Edge of each Standard at the Top, as at b b and b b, for the more easy Admission of the Spindle of the Marking-wheels into the Forks: This Spindle is kept in its Place by Two of the same sort of Wreaths, and placed in the same manner as those describ’d for the fore Hopper of the Wheat-drill.

Such Marking-wheels are necessary for drilling upon the Level; but not for drilling upon Ridges.

E is the Beam, Two Feet Two Inches and an half long, Four Inches broad, and Two Inches thick: It is thus broad, that the Screws which hold on the cross Piece F, may be farther asunder: The Screws must be placed as near as may be to the Outsides of the Beam, and at equal Distance from each Side of the cross Piece; by which means the Standards are kept the firmer from Turning.

The Distance between the Plank and the cross Piece is Eleven Inches. The Breadth of the cross Piece is Two Inches and a quarter. This cross Piece is shewn apart in Fig. 2. where its Two Standards A B, are each Seventeen Inches long (or high), and each on its fore Side and hinder Side One Inch and a quarter broad, and nearly Three quarters of an Inch thick: They are shoulder’d and pinn’d into the cross Piece at a b. The cross Piece is Thirteen Inches and an half long, and one Inch and a quarter thick in the Middle from c to d; but for about an Inch on the Inside of each Standard is Two Inches and an half thick, that the Standards may have the more Wood to support them, and that the Hopper, bearing upon the thicker Parts of the cross Piece, may be held up above the Funnel, that the Fork of the brass Spindle may not strike against it, when the Plough is taken up to be turn’d, there being a little more than a quarter of an Inch of the Breadth of the cross Piece behind the Standard, for the Hopper to rest on.

The whole Distance between the Standards is Nine Inches and a quarter. The Standards must be exactly perpendicular to their cross Piece: Their Tops are drawn up each to a Point, as at e and f, by which the Hopper is the more easily put on upon them.

The Funnel, Sheat, Share, and Trunk, are the same as those in the Wheat-drill, except a few Differences: As G in Fig. 1. is the same as the fore Sheat of the Wheat-drill, with its Accoutrements; only it is lower, being but Eight Inches high from the Bottom of the Share up to the Beam; and the Plates of the Trunk are somewhat narrower: Its Tenon passes thro’ the Beam, and comes up above it, betwixt the Funnel and the cross Piece; and there is pinn’d in thro’ its Hole above the Beam. There is no want of Wood behind the Sheat, the Funnel not being cut in the Beam, but placed upon it.

The Funnel is shewn apart in Fig. 3. and is Two Inches deep, Four Inches square at Top; its Four Sides terminating at an Hole in the Bottom, half an Inch broad from a to b, and near an Inch long from c to d, which Length is divided in the Middle, by the upper Edge of a Brass Spout, which divides the Hole into Two equal Parts (or Holes), each of which is about half an Inch square; this Funnel being screw’d on upon the Beam by Two Wood Screws, entering at Two opposite Corners of the Funnel, as at c d in Fig. 1. so that the Seed may drop from the Seed-box upon the right Side of the Funnel at e, which being about half an Inch distant from the Partition, and equidistant from both Holes, the Seed rebounding is pretty equally distributed to each of the Holes.

The fore Part of the foremost Hole being equal with the Back of the Sheat, the Beam being cut thro’; so that the Back of the Sheat, and the fore Part of the Hole thro’ the Beam, and the fore Part of this Hole, make one plain Surface, whereby the Seed that falls into this foremost Hole, descends to the Ground, near the Back of the Sheat, thro’ the Trunk.

And the Seed which falls into the hinder Hole, is convey’d obliquely backwards thro’ Part of the Beam, by a short thin Brass Spout, whose Diameter in the Inside is somewhat more than half an Inch; but the fore Part of it, which divides the Two Holes, descends first perpendicularly half an Inch, and then turns off backwards, and there the Spout begins to be round: Its joining is on its hinder Part, to the end that the Seed, never running upon it, cannot be stopp’d by it. The lower End of this Spout ends at the lower Surface of the Beam, a little behind the Plates of the Trunk, which Hole is seen at a in Fig. 4. where this Hole delivers the Seed down into the Spout A, when it is drawn up into its Place by the String B drawn thro’ the Hole at b in the End of the Beam, and there tied until it stand in the Posture in which it is seen at f in Fig. 1.

The Shape of this Spout is better seen at Fig. 5. where A is the Spout, Four Inches long, a full Inch Diameter in the Inside: Its lower End is circular; but its upper End B is cut at oblique Angles, so that when it is drawn up to its Place, its Edges will touch the lower Surface of the Beam, and inclose the lower End of the other Spout within it: It is made of thin hammer’d Brass (as is the other). The Edges of the Piece of Brass, which make this Spout, are join’d on its hinder Part, for the same Reason that they are so in the other Spout. At b there is a Jag cut in one of these Edges, and rais’d upwards, by which Jag the String being tied on the Spout just below, is hindered from slipping upwards.

Joining to the highest Part, and made with Part of the same Piece of Brass, turn’d back from the End of the Spout, is its Hinge C, near Three quarters of an Inch long in its Hollow.

D is a thin Piece of Iron, half an Inch broad, and a little longer than the Top of the Sheat, by which the Spout is held up: This Piece of Iron is riveted by a Rivet passing thro’ an Hole at c, and thro’ the Sheat, just before the Trunk, and thro’ another Piece of Iron on the opposite Side; both the Pieces of Iron, with their upper Edges touching the Beam, being thus riveted to the Sheat.

The Spout is pinned in by the Screw E, passing as by the prick’d Line F thro’ the Hole G, and also thro’ the Hinge C, and screw’d into the Hole of the opposite Piece of Iron, corresponding with the Hole G; and then it will appear as in Fig. 4.

Instead of these Pieces of Iron, we sometimes use Pieces of Wood, a little broader and thicker, nail’d on the Sheat.

The Use of this Spout is for carrying half of the Seed backwards, so that it may drop upon the Chanel, after the Earth is fallen into it: By this means the Seed lying very shallow, being only cover’d by a little Earth rais’d by the Harrow, by its Shallowness comes up in moist Weather, sooner than the other half, which lies deeper in the Ground; but if the Weather be dry when planted, the deeper half, by the Moisture of the Earth from the Dews, will come up first, and the shallow half will not come up till Rain come to moisten it; so that by the shallow or deep, the Turnep-fly is generally disappointed.

Fig. 6. shews one of the Tines of a Drill-harrow made of Wood: Its Edge a b is made roundish at b, by which means it raises the Earth on its Sides; but does not drive it before: This Edge from a to b is Six Inches long; from b to c, being its Bottom, is One Inch and a quarter; from c to d is the Back, an Inch and an half thick at Top, gradually tapering downwards to c, where it is half an Inch thick, being shoulder’d all round: It has a flat Tenon A, which passes thro’ a Mortise in the Harrow-head; the Length of which Mortise is parallel with the Length of the Harrow-head, into which it is held by a Pin, passing thro’ the Hole of the Tenon, above the Harrow; as may be seen in Fig. 7. at a; and its Fellow at b.

These Two Tines are Eight Inches asunder at their Points, and Six Inches and a quarter asunder at their upper Parts, just under the Harrow-head. The fore Edge of the Tine A inclines a little to the Left, as the Edge of the Tine B doth to the Right.

Fig. 8. shews one of the Legs of the Harrow. At a is seen the round Tenon, which passes thro’ the Harrow-head up to its Shoulder, and is pinned in thro’ an Hole of the Tenon just behind the Harrow-head; upon this Tenon the Harrow-head may turn: The other End has an Hole at b, thro’ which it is pinned on to the Beam. The Length of the Leg from the Shoulder at a, to the Hole at b, is Twenty Inches: Its Thickness is an Inch and a quarter, and its Breadth an Inch. The Two Legs are seen mark’d C, D, in Fig. 7. They bend down in the Middle, to give the Harrow the more room for rising and sinking; they are parallel to each other, and distant a little more than the Breadth of the Beam, that they may have Liberty to move thereon, when one End of the Harrow-head sinks lower than the other, by the Unevenness of the Ground.

The Harrow is pinned on to the Beam by the Iron Pin, Fig. 9. passing thro’ the Hole of the Leg at g, and thro’ the Beam, and also thro’ the other Leg on the other Side of the Beam, where the Screw at the End of the Pin has a Nut screw’d on it. This Pin is round from its Head all the Way thro’ the first Harrow-leg, and thro’ the Beam; but all that Part of the Pin, which is in that Leg against which the Nut is screw’d, must be square; whereby that Part being bigger than the round Part of the Pin, and than the Hole in the last-mention’d Leg, cannot turn in the Hole of that Leg; for if it did, the Nut would be soon unscrew’d by the Motion of the Harrow; but the Pin must have room to turn in the other Leg, and in the Beam. This square Part of the Pin is seen at a, Fig. 9. The whole Length of the Pin, from its Head to the End of the square Part at a, where the Screw begins, is of the Thickness of the Two Legs, and of the Breadth of the Beam.

We sometimes set the Legs of the Harrow Two Inches wider asunder, by making them each an Inch thicker at their fore Ends in their Inside, and reaching Five or Six Inches behind their Iron Pin: These thicker Parts, bearing against the Beam, keep the hinder Part of each Harrow-leg an Inch distant from the Sides of the Beam, whereby the Harrow-legs are Six Inches asunder, instead of Four, by means of these added Thicknesses.

When a Drill is taken up to be turn’d, the Person that does it, takes hold of the Harrow-head, and lifts it up: The Legs of the Harrow, bearing against the cross Piece, support the whole Weight of the Drill.

When the Harrow does not go deep enough, we tie a Stone upon the Middle of the Harrow-head, by a String that passes thro’ the Holes at h. All the Wood of this Plough and Harrow is Ash, except the Limbers.

The Hopper of the Turnep-drill is very different from those already described. It consists of a Box placed into the Middle of a Carriage; which Box is described in all its Parts, lying open with their Insides upwards in Fig. 10. A is the fore Side of the Box, Five Inches and an half deep, and Six Inches and an half long. B, the hinder Side of the Box, opposite to the former, and of equal Dimensions.

Each End of the Box is made with Three Pieces of Board, of which C the uppermost is Three Inches and a quarter deep, and Five Inches long; which Length is the Breadth of the Inside of the Box. The End of the Piece C, when in its Place, stands against the prick’d Line a b in the fore Side A; the other End standing against the prick’d Lines in B, which is opposite to, and corresponds with, the prick’d Line a b; the fore Side, and hinder Side, being screw’d to the Ends of this Piece by Four Screws.

The Piece D is Two Inches and a quarter broad, and of the same Length with the Piece C, and screw’d up to the Bottom of it with Two Screws, and then its End will bear against the prick’d Line b c, and that which is opposite to it in the Side B.

E is the lower Piece of this End, and an Inch and a quarter broad: Its End is to stand against the prick’d Line c d, and its other End at the opposite prick’d Line in B. The Piece D must be screw’d upon the upper Edge of the Piece E, as the Bottom F must be screw’d up to its under Edge, which will stand upon the prick’d Line e f. The Three Pieces G, H, I, being opposite to C, D, E, and of the same Dimensions with them, placed in the same manner, make the other End of this Box. At g in the Bottom F, appears the Hole which is over the Mortise of the Brass Seed-box, the Shape and Size of which Hole may be seen by the prick’d Lines upon the Flanches B, C, of Fig. 9. in Plate 2. The foremost End of which Hole reaches almost as far forwards as the End of the Axis of the Tongue of the Brass Seed-box, and its hinder End almost as far as the hinder End of its Cover[269]. The Bottom F, being of the same Length, with C, D, E, and their Opposites, bears against the prick’d Line d h of the fore Side A, and against the opposite prick’d Line of B. The Length of this Bottom F is the Breadth of the Inside of the Box, and its Breadth reaches to the outer Edges of the Pieces E and I, being Three Inches and an half.

All the Jointings of these Pieces must be at right Angles, and so close, that no Seed may run out at them. All the Pieces are of Board, full half-inch thick, except the Bottom, which is thinner.

Fig. 11. shews the Bottom of the Box with its under Side uppermost, where the light Part A is the Bottom-board, covering the Two End-boards, E and I, in Fig. 10. The dark Parts B and C are the under Sides of D and H, in Fig. 10. At a is the fore End of the Brass Seed-box screw’d up to this Bottom-board. At b is the hinder End of the Brass Seed-box screw’d up in like manner, the outer Edge of the Flanch of the Seed-box being even with the Edge of the Bottom-board. The End of the Brass Spindle, with its Fork, appears at C.

Fig. 12. shews this Box standing upon its Bottom, with its hinder Side laid open. At a is the Hole in the Bottom, under which the Brass Seed-box is fasten’d, with small Iron Screws, square near the Heads, passing thro’ the Bottom, and thro’ the Holes at each End of the Brass Box, with their Nuts underneath. The Pins must touch all the Sides of the Holes in the Brass, to prevent the Seed-box from moving any Way.

A is the fore Side of the Box. B the hinder Side lying down. C is the Piece H of Fig. 10. which makes a sort of Shelf in the Box at its left End. D at the right End makes another like Shelf, underneath which, the Fork of the Brass Spindle is turn’d by the Crank in the End of the wooden (false) Spindle. By means of these Shelves, there is room for the Two wooden false Spindles to come the further into the Carriage, without lessening the upper Part of the Box. E and F are the Two Ends of the upper Part of the Box, made by the Two Pieces G and C of Fig. 10. When the hinder Side B is rais’d up, and screw’d to these Ends, the Box is complete.

We put a Lid upon this Box, which is hing’d on to its right or left End. This Box (having the Brass Seed-box at its Bottom) is to be placed into the Middle of a Frame or Carriage.

Fig. 13. shews the Inside of the Carriage lying down. A is the hinder Side, Eighteen Inches long, Dove-tails and all, and Six Inches broad. B the fore Side of the same Length with the hinder Side, and Eleven Inches broad. This Five Inches greater Breadth than the hinder Part is, because a greater Height is required on the fore Side, on account of the Hopper’s being drawn, and the Plough held up by that and the Pieces that must be fix’d to it. C, D, are its Two Ends, Six Inches long, beside their Dove-tails, and Six Inches broad. E and F are Two Pieces each Six Inches long, whose Ends are to stand against the prick’d Lines a b and c d of the hinder Side, and their other Ends against the prick’d Lines in the fore Side, which are opposite to these. The Breadth of each of these Pieces is Four Inches: When they are in their Places, their lower Edges come even with the Bottom of the Carriage. Their Use is to support the Ends of the Spindles which come just thro’ their Holes, after each of them have passed their Hole at its respective End of the Carriage.

All this Carriage is made of Board full half-inch thick; The Ends C and D are made of double Thickness by another Piece of Board added to each, that covers all their Insides, except their Dove-tails. These Boards with which they are lin’d, are nail’d to them, with their Grain going a different Way, and crossing the Grain of the Board at the End, either at right or oblique Angles. This prevents the Holes from splitting out, and makes the Holes of a double Thickness; whereby the Spindle is the less worn by them, in case there are no Brass Wreaths to enter them.

The middle Pieces E and F are lin’d by their whole Surfaces, in the same Manner as the Insides of the Ends are lin’d.

When these Ends and middle Pieces are in their Places, a wooden Cylinder, of the exact Diameter of the Holes, is thrust thro’ all Four, to hold them exactly true, whilst the Ends and middle Pieces are all screw’d fast into their Places.

The prick’d Lines are drawn all round the Carriage, thro’ the Centres of the Holes, and at equal Distance from the Bottom of the Carriage, which is an Inch and Three quarters, and the One-eighth of an Inch. This prick’d Line is a Direction how high to nail on the Ledgers G and H, whereon the Box is to stand; and the Distance the upper Surface of the Ledger must be above the prick’d Line, is the Semidiameter of the Brass Spindle; and the Thickness of the Brass Box above the Spindle, or which is the same thing, the Distance between the Centre of the great Hole of the Brass Seed-box, and the Plane of the Top of its Mortise, being half an Inch and half a quarter, strike a Line above the prick’d Line parallel to it, at this Distance above, and then nail on the Ledger, with its upper Edge at this Line. This, with its opposite Ledger plac’d in the same manner, will support the Box with the Axis of the Spindle of the Seed-box, at equal Height with the Centres of the Holes of the Carriage; so that if those Holes are parallel to, and equidistant from the fore Side and hinder Side of the Carriage, and the Axis of the Brass Spindle be placed in the like manner parallel to, and equidistant from the fore Side and hinder Side of the Box; then when the Box is thrust down in its Place, upon these Ledgers, and the wooden (false) Spindles are placed into their Holes, their Axis will fall into a strait Line with the Axis of the Brass Spindle, as they ought.

Fig. 14. shews the Carriage laid open. A is its back Side lying down. B is its fore Side standing up. C is the square End of the left (false) Spindle, whereon a Wheel is to be put up to the Shoulders of the Spindle, quite close to the Ends of the Carriage. This Spindle, being an Inch and an half Diameter, is held in its Place, and kept from moving end-ways, by Two Wreaths; the one at a, bearing against the Inside of the End of the Carriage, the other Wreath at b, bearing against the left Side of the middle Piece; which Wreath keeps the Spindle from moving towards the right Hand, as the other does from moving towards the left. D is the square End of the other wooden Spindle, whereon a Wheel must be placed in the same manner as the other Wheel. This Spindle is kept from moving end-ways by Two Wreaths, in the same manner as the other Spindle is; but this right-hand Spindle, being that which turns the Brass Spindle by its Crank, which enters the Fork, should have its Wreaths of Brass, like those describ’d in Fig. 17. Plate 4. Part of which Wreaths entering about Three quarters of an Inch into the Hole of the End and middle Part of the Carriage, being firmly screw’d on to the Spindle, prevent the Friction that would otherwise be betwixt the Wood of the Spindle, and the Wood of the Holes; which Friction wearing the Wood of both, would in time cause the Spindle to be loose in its Holes, whereby its Axis would deviate from the strait Line it should make with the Axis of the Brass Spindle, and make an Angle with it; and then the Crank would change its Place in the Fork at every Revolution of the Wheels; and if the Hole should be worn very wide, and the Spindle worn much less, the Crank might let go the Fork; but when the Wood is of this Thickness, and each Hole has Wood in it, with its Grains pointing different ways, it would be many Years before the Holes would become large enough for this to happen, tho’ only wooden Wreaths were used; and as to the Two Wreaths of the left Spindle, they may be of Wood, because tho’ that Spindle should grow loose, it is no Damage; for it only serves to bear up that End of the Carriage; but he that has this Sort of Brass Wreaths for the hinder Hopper of a Wheat-drill, may take them thence, and place them upon these Spindles, and remove them again to the Wheat-drill when that is used; for that and the Turnep-drill are very rarely, or never, used at the same time.

E is the Iron Crank, plac’d into the false Spindle, in the manner shewn at H in Fig. 5. of Plate 2. for turning the Brass Spindle by its Fork; but take care that the End of this wooden Spindle do not approach nearer to the End of the Brass Spindle than the Distance of half an Inch, left, if the inner Wreath should grow loose, the wooden Spindle might bear so hard against the Brass one, as to wrench the Seed-box down from the Wood, and then the Seed might run out betwixt the Seed-box and the Bottom to which it is screw’d.

When the hinder Side A is screw’d up against the Ends and middle Pieces, then the Box describ’d, being thrust down into the Carriage, and standing upon the describ’d Ledgers, and at that Distance from each End of the Carriage, that the Seed may drop on the Side of the Funnel, as is before describ’d; the Box is kept in its Place by one Screw passing thro’ its Back, and the back Side of the Carriage.

The Notch F is cut in the Bottom of the hinder Side of the Carriage, up to the Bottom of the Ledger, for the Convenience of seeing the Seed drop into the Funnel.

The round Notch G is made in the Bottom of the fore Side of the Carriage, to make room for one’s Hand to go in there, and turn the Setting-screw without taking off the Hopper from the Standards.

This Box and Carriage, so fix’d together, compose the Turnep-hopper, which is drawn and guided, and also holds up the Plough, by Two hollow Pieces of Wood screw’d on to the Outside of the fore Part of the Carriage; their Ends H and I appearing a little above the Carriage.

One of these hollow Pieces of Wood is shewn in Fig. 15. The Breadth of its Hollow must conform to the Breadth of the Standards, which are One Inch and a quarter broad; but we must allow about a quarter of an Inch more in the Hollow for the Swelling of the Wood. The Depth of the Hollow must be the Thickness of the Standard that is to go in it, allowing about the Eighth of an Inch for the Swelling of the Wood. The Hollow should be a little deeper in the Middle than at each End; because the Standard ought not to bear against any thing, except at or near the upper and lower Part of the Carriage. Altho’ the End of these Pieces come a little higher than the Carriage in this Hopper, yet I think it is better that these hollow Pieces come no higher than even with the Top, nor descend any lower than even with the Bottom of the Carriage; and then the Length of each of these Pieces need be no more than Eleven Inches, which is the whole Depth of the Carriage.

The Wood on each Side of the Hollow, sufficient for the Holes a, a, a, a, must be about half an inch broad. The best way for fixing them on, is whilst the Standards are in them, placing a small Piece of Wood at each Corner of the Hollow, betwixt the Standard and the Wood, to the end that there may be no more room on one Side of a Standard than on the other Side; then screw them on (parallel to and equidistant from their respective Ends of the Carriage) by Four small Screws each, the one at c, c, c, c, and the other at d, d, with Two below; the Heads of these Screws being on the Inside of the Carriage, and their Nuts on the Outsides of the hollow Pieces; then pull out those little Pieces of Wood, that were to keep the Standards in the Middle of the Hollows, whilst the Holes for the Screws were bored, and then the Turnep-Hopper is finished, and being put on upon the Standards A, B, in Fig. 16. is ready to go to Work; and in this Figure the whole Turnep-drill may be seen as in the Prospect of a Person following it at Work, except that this Figure has not the double Standard, nor Marking-wheels; because we never use them for drilling-Turneps, except it be on the Level, which we very rarely do.

The Circles of the Wheels of this Hopper go Twenty five Inches asunder; were they farther asunder, they would not go so well upon the Ridges; or were they nearer together, they might not hold up the Plough so steadily, but that one Wheel might happen to be rais’d from the Ground, by the descending of the opposite Limber; and if it should happen to be the Wheel that turns the Crank, no Seed would be deliver’d out whilst the Wheel was rais’d above the Ground; sometimes we use Wheels of Twenty-six Inches Diameter, sometimes Thirty, and at intermediate Diameters, with this Hopper.

The best Wood for making all Sorts of Hoppers is Walnut-tree or Elm; our Beams and Standards we make of Ash.

What is meant by Wood-screws, are taper Screws made with Iron, having very deep Threads, whereby they hold-fast when screwed into Wood, and their Points will enter into soft Wood without boring any Hole for them into the Wood they are to take hold of; but near their Heads they are round, and have no Thread, and that Part of them must always be in a bored Hole thro’ that Part of a Board that is to be drawn close.

If the Standards should be much swollen by being wet, it may be proper to anoint them with Soap.

In drilling, when the Wind is very strong, and the Hopper goes high above the Funnel, the Seed might be blown over it, if we did not take care to guard it from the Force of the Wind; and for doing this there are many Ways: Sometimes we nail a Piece of Linen Cloth round the Ends, and the fore Side of the Hopper; or else we nail on a Piece of old Hat, or Shoe-leather, round the Edges of the Funnel, to raise it higher; or if the Hopper go a great deal above the Trunk, we nail up a Pipe of Leather to the wooden Bottom of the Box, which Pipe, being about an Inch wide at Bottom, protects the Seed from the Wind, till it arrives so near the Funnel, that the Wind cannot blow it over.

If we would have a long Hopper, to plant many Rows at once, of Clover or other fine Seeds, it is easy to make each of these wooden (false) Spindles turn Two or Three Brass or Iron Spindles; but then, as in all other Cases; where the same Hopper is to supply more than one Chanel with Seed, each of its Wheels must have Liberty to rise without the other, as those of the hinder Hopper of the Wheat-drill do.